Teejet Fieldware SA 2.0 for Legacy 6000 Uživatelský manuál Strana 107
- Strana / 172
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Fieldware-SA for the Legacy 6000
Software Version 2.00
Chapter 4 - Real-time Operation 4-15
Real-time Guidance Operation
The Headland Guidance Pattern
This section describes how to operate the Headland guidance pattern. The Headland pattern is
selected when the operator wants to drive several circuits around the field boundary and be guided
around all circuits that occur after the first circuit. When several headland circuits have been com-
pleted, the operator then has the choice of switching back to the Straight-Line pattern. The Head-
land pattern is also selected when a user wants to do product application on terraced fields. In the
Headland curved guidance pattern, the operator can pull along side any previous applied swath
and be guided parallel to that swath.
Applying Multiple Headland Circuits
Figure 4-11 shows the Map page when the Headland pattern is selected. While operating in the
Headland pattern, the user has the option to mark the A and B points for the Straight-Line pattern.
This feature makes it easier for the operator to Mark the A and B points while in curved mode
applying the headlands. It is always best to mark the A and B points for the Straight-Line pattern
while driving along a straight edge of a field.
The operator remains in the Headland pattern until the pattern is changed using the Guidance Pat-
tern soft-key (see Changing Guidance Pattern on page 4-12). The A and B points are only required
for the Straight-Line pattern. The Headland pattern does not require an A-B line.
Figure 4-11: Operating in Headland Pattern
Guidance Pattern
Soft-key
- USER GUIDE 1
- Table of Contents 2
- 3 3
- Fieldware - SA Version 2.00 5
- System Introduction 6
- Legacy 6000 System Features 7
- Activation Description 8
- Legacy 6000 Console 10
- Chapter Notes 12
- Chapter 2 - Getting Started 13
- Software Overview 14
- Standard Pages 16
- Setup Menu Page 18
- Setup Wizard 18
- Setup Sub-Groups 18
- Exiting a Setup Menu Page 18
- Data Entry Page 20
- Pick List Data Entry 20
- Alpha/Numeric Data Entry 20
- Exiting a Data Entry Page 20
- System Setup 22
- Modes of Operation 23
- Rate Control Mode 24
- Console Setup 25
- Setting Description 26
- Lightbar Setup 27
- GPS Receiver Setup 29
- Implement Setup 31
- Entering the Implement Width 33
- Completing Implement Setup 36
- Figure 2-18: Boom Sense Cable 37
- Entering the Section Width 40
- The Offset Distance Y 40
- Controller Setup 43
- Compatible Rate Controllers 44
- Backing up System Files 45
- System Tools 46
- Tool Description 47
- Table 2-10: System Tools 47
- The Device Manager 48
- Button Description 50
- Required Items: 51
- Card Manager 54
- Chapter 3 - Real-time Setup 57
- Real-time Setup Steps 58
- Step Description 59
- Setting up a Job 60
- Creating a New Job 61
- No PCMCIA Card 61
- ARM Launcher 62
- No PCMCIA Card Setup 63
- Setting up a Report 64
- Item Description 65
- Enter the Wind Speed 66
- Enter the Wind Direction 67
- Enter the Temperature 67
- Enter the Relative Humidity 68
- Select the Soil Moisture 69
- Select the Soil Condition 69
- Select the Soil Texture 70
- Select the Soil Tillage 70
- Select the Growth Stage 71
- Running ARM Setup 72
- Table 3-4: ARM Setup Items 73
- Running the ARM Setup Wizard 74
- No PCMCIA Card Selected 75
- Select / Enter a Record File 76
- Select Enter a Guideline File 77
- Enter the System Delay Value 80
- Running Product Setup 81
- Select The Prescription Map 83
- Select the Product Name 85
- Favorites 85
- New Product 85
- Start to type name here 86
- Highlight this window and 86
- Figure 3-36: Selecting a Job 88
- Importing Into a Running Job 89
- Product Application 94
- Real-time Pages 95
- The Rates Page 96
- The Map Page 98
- Soft-key Description 100
- System and Warning Messages 102
- Figure 4-8: Warning Message 103
- Real-time Guidance Operation 104
- Mark Point A 106
- Mark Point B 106
- The Headland Guidance Pattern 107
- Headland Pattern Example 108
- Software Version 2.00 109
- Circle Pivot Example 120
- Marking Point A 120
- Marking Point B 120
- Applied Area Detection 126
- Mapping a Field Boundary 127
- Figure 4-38: Naming the Point 130
- Marking a Hazard 131
- Object Name File 131
- Exiting Real-Time Operation 132
- Lightbar Index 134
- Lightbar State Description 135
- Fieldware-SA Version 2.00 139
- FieldPilot Introduction 140
- Powering Up 145
- Running FieldPilot Setup 146
- Setup Item Description 147
- Real-time Setup 148
- Real-time Operation 149
- Setup Description 150
- The Nudge/Trim Feature 155
- Chapter 6 - Manual Guidance 159
- Manual Guidance Introduction 160
- Chapter 7 - Fieldware - SA 165
- Installation Overview 166
- Figure 7-2: Single Setup Type 168
- Figure 7-3: Repeat Setup Type 168
- Setup Ready to Run 169
- Finishing the Version Update 170
Související produkty a manuály pro Počítače Teejet Fieldware SA 2.0 for Legacy 6000
Počítače Teejet Swath XL SmartPad II Uživatelský manuál
(204 stránky)
(204 stránky)
Počítače Teejet Swath XL Uživatelský manuál
(162 stránky)
(162 stránky)
Počítače Teejet CenterLine 230BP Uživatelský manuál
(26 stránky)
(26 stránky)
Počítače Teejet CenterLine 230BP Uživatelský manuál
(23 stránky)
(23 stránky)
Počítače Teejet CenterLine 230BP Uživatelský manuál
(23 stránky)
(23 stránky)
Počítače Teejet CenterLine 230BP Uživatelský manuál
(23 stránky)
(23 stránky)
Počítače Teejet CenterLine 230BP Uživatelský manuál
(21 stránky)
(21 stránky)
Počítače Teejet CenterLine 230BP Uživatelský manuál
(15 stránky)
(15 stránky)
Počítače Teejet CenterLine 230BP Uživatelský manuál
(15 stránky)
(15 stránky)
(2 stránky)© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.072 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce